CTC Union FSW3208M Specifications

FSW3208M 8+2 Gigabit Ethernet WebSmart Switch

10 2.1 Configurations 2.1.1.1 System information The system diagram shows general common system information, they are H/W, F/W version, MAC addre

11 2.1.1.2 DHCP The default DHCP is off, so Default IP or user defined IP is used when this machine is turning-ON, but if this switch needs an IP ass

12 2.1.2 Ports Port status page always shows current port status of all 8 ports. User can set link mode, enable or disable flow control and jumbo f

13 2.1.3 Port-based VLAN Port-based VLAN is a kind of VLAN which is a group of ports marked as a kind by group ID, different VLAN (different ID) can’

14 2.1.4 Tag-based VLAN Tag-based VLAN is another kind of VLAN which is a group of ports marked as same kind by assigning a tag-value on each port, s

15 If VLAN 10 and VLAN ID 20 must be isolated, then user must delete member port 5,6,7,8 in default VLAN group(VID = 1). See below

16 1. VLAN Aware mode: Enable – When Tag-VALN function is applied on this port, user may enable VLAN Aware associated with this port, then ing

17 2.1.5 Port Trunking A default diagram is shown below, and up to 4 groups are provided Choose and click the trun

18 2.1.6 Port Mirroring A default diagram is shown below, Choose and click the ports you want to monitor, for example, choose

19 2.1.7 Quality of Service There are 4 class priority can be set for each port: Low, Normal, Medium and High, because there are 8 priority levels (

20 When user choose the 802.1P priority, this means frames are with VLAN Tag inside the switch, the priority in the Tagged frame (2 bytes T

21 2.1.8 Storm Control A default diagram is shown below, Choose and click type of storm you want to control, for example, choose B

22 2.1.9 LACP Different from the static port trunking, LACP provides another way to dynamically aggregate port to a group (trunk) according to IEEE 8

23 2.1.10 RSTP The Spanning-Tree Protocol (STP) is IEEE 802.1d standardized method for avoiding loops in switched networks. Enable STP to ensure t

24 Use the following parameters in the webpage to configure RSTP function:  System Configuration  System Priority – A value to identify the roo

25 2.1.11 IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IGMP can manage

26 2.1.12 802.1x A default diagram is shown below, user must contact the manager of RADIUS server, and then get IP, UDP port number (usually fixed at

27 2.2 Monitoring 2.2.1. Port Statistics Choose and click command manual, after execution, diagram will shown below, user can clear coun

28 2.2.2 LACP Status Choose and click command manual, after execution, diagram will shown like below, user can refresh at will.

29 2.2.3 RSTP Status Choose and click command manual, after execution, diagram will shown like below, user can refresh at will.

LEGAL The information in this publication has been carefully checked and is believed to be entirely accurate at the time of publication. CTC Union Te

30 2.2.5 Ping Fill up the IP address you want to ping, set Time Out time and Counts, for example, IP = 192.168.223.25441,

31 2.3 Maintenance 2.3.1 Warm Reboot Choose and click command manual, diagram will shown like below, user can press Yes or No Warm Reboot Are you

32 2.3.4 Config File Choose and click command manual, diagram will be shown, and then direct the location of the file that is to be backup, give a n

33 Key in " Command " and then key in " ? ", second level will be shown , for example

34 If user wants to check the IP related information, he may do as below All other function can be operate likewise. Type "

CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60, Zhouzi St. Neihu, Taipei, 114 Taiwan Phone

TABLE OF CONTENTS 1.0 INTRODUCTION...

7 1.0 Introduction This web smart switch is a high speed switch that provides up to 8 10/100/1000Mbps copper Ethernet ports, besides, it provides man

8 1.2 Start to Manage This Switch Either way user may start to manage this switch, web mode through Ethernet port or terminal mode through RS232 port

9 2.0 Web management After login is successfully validated, the switch’s home page will show up. The left part on the page provides the function